360R-06 Design of Slabs-on-Ground
tải về 2.35 Mb. Chế độ xem pdf
|
- Điều hướng trang này:
- 360R-58 ACI COMMITTEE REPORT
| CHAPTER 14—REFERENCES
14.1—Referenced standards and reports The standards and reports listed below were the latest editions at the time this document was prepared. Because these documents are revised frequently, the reader is advised to contact the proper sponsoring group if it is desired to refer to the latest version. American Concrete Institute 116R Cement and Concrete Terminology 117 Standard Specifications for Tolerances for Concrete 201.1R Guide for Making a Condition Survey of Concrete in Service 209R Prediction of Creep, Shrinkage, and Temperature Effects in Concrete Structures 211.1 Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete 223 Standard Practice for the Use of Shrinkage- Compensating Concrete 224R Control of Cracking in Concrete Structures 302.1R Guide for Concrete Floor and Slab Construction 311.5 Guide for Plant Inspection and Field Testing of Ready-Mixed Concrete 318 Building Code Requirements for Structural Concrete Fig. 13.7—Representative curling deflection curves for 20- and 40-ft slabs with an effective temperature difference of 30 °F between top and bottom (Leonards and Harr 1959). (Note: 1 psi = 0.006895 MPa; 1 in. = 25.4 mm; 1 °F [ ΔT] = 0.56 °C; 1 lb/ft 3 = 0.2714 MN/m 3 .) 360R-58 ACI COMMITTEE REPORT 330R Guide for Design and Construction of Concrete Parking Lots 350 Code Requirements for Environmental Engi- neering Concrete Structures 336.2R Suggested Analysis and Design Procedures for Combined Footings and Mats 504R Guide to Sealing Joints in Concrete Structures 544.1R Fiber Reinforced Concrete 544.2R Measurement and Properties of Fiber Reinforced Concrete 544.4R Design Considerations for Steel Fiber Reinforced Concrete ASTM International A 36 Specification for Carbon Structural Steel A 497 Specification for Steel Welded Wire Reinforce- ment, Deformed, for Concrete Reinforcement A 615 Specification for Deformed and Plain Carbon Steel Bars for Concrete Reinforcement A 706 Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement A 820 Specification for Steel Fibers for Fiber-Rein- forced Concrete A 996 Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement C 150 Specification for Portland Cement C 157 Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete C 494 Specification for Chemical Admixtures for Concrete C 595 Specification for Blended Hydraulic Cements C 845 Specification for Expansive Hydraulic Cement C 878 Test Method for Restrained Expansion of Shrinkage-Compensating Concrete C 1399 Test Method for Obtaining Average Residual- Strength of Fiber-Reinforced Concrete D 422 Method for Particle-Size Analysis of Soils D 566 Test Method for Dropping Point of Lubricating Grease D 698 Test Methods for Laboratory Compaction Characteristics of Soil Using Standard Effort (12,400 ft-lpf/ft 3 (600 kN-m/m 3 )) D 854 Test Method for Specific Gravity of Soil Solids by Water Pycnometer D 1196 Test Method for Nonrepetitive Static Plate Load Tests of Soils and Flexible Pavement Components, for Use in Evaluation and Design of Airport and Highway Pavements D 1556 Test Method for Density of Soil in Place by the Sand Cone Method D 1557 Test Methods for Laboratory Compaction Char- acteristics of Soil Using Modified Effort (56,000 ft-lpf/ft 3 (2700 kN-m/m 3 )) D 1586 Test Method for Penetration Test and Split- Barrel Sampling of Soils D 1621 Test Method for Compressive Properties of Rigid Cellular Plastics D 1883 Test Method for CBR (California Bearing Ratio) of Laboratory-Compacted Soils D 2167 Test Method for Density and Unit Weight of Soil in Place by the Rubber Balloon Method D 2216 Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass D 2240 Test Method for Rubber Property—Durometer Hardness D 2487 Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System) D 2488 Practice for Description and Identification of Soils (Visual-Manual Procedure) D 2922 Test Methods for Density of Soil and Soil- Aggregate in Place by Nuclear Methods (Shallow Depth) D 2937 Test Method for Density of Soil in Place by the Drive-Cylinder Method D 3017 Test Method for Water Content of Soil and Rock in Place by Nuclear Methods (Shallow Depth) D 3575 Test Methods for Flexible Cellular Materials Made from Olefin Polymers D 4253 Test Methods for Maximum Index Density and Unit Weight of Soils Using a Vibratory Table D 4254 Test Methods for Minimum Index Density and Unit Weight of Soils and Calculation of Relative Density D 4263 Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method D 4318 Test Method for Liquid Limit, Plastic Limit, and Plasticity Index of Soils F 1869 Test Method for Measuring Moisture Vapor Emission Rate of Concrete Subfloor Using Anhydrous Calcium Chloride F 2170 Test Method for Determining Relative Humidity in Concrete Floor Slabs Using in situ Probes The above publications may be obtained from the following organizations: American Concrete Institute P.O. Box 9094 Farmington Hills, MI 48333-9094 ASTM International 100 Barr Harbor Drive West Conshohocken, PA 19428-2959 tải về 2.35 Mb. Chia sẻ với bạn bè của bạn:
|