UniClean 284 ds v1


Agitation  Revolution recommended  Filtration



tải về 54.76 Kb.
Chế độ xem pdf
trang3/5
Chuyển đổi dữ liệu18.06.2022
Kích54.76 Kb.
#52401
1   2   3   4   5
UniClean 284 ds v1

Agitation 
Revolution recommended 
Filtration 
Not required 


UniClean 284 
Electrolytical cleaner for zinc die castings, brass and copper 
Version: 01 
Doc.-No.: 5200 
Page: 3 / 7 
Released on: 
 
 
Released by: 
10.11.2011 
BTT CSP 
4. Make-Up 
Make-Up of 100 l 
Make-up 
Range 
for copper and copper alloys
UniClean 284 
5 kg 
3 – 7.5 kg 
for zinc die castings
UniClean 284 
3 kg 
2 - 4 kg 

Fill tanks to approx. 70 % of the volume with water. 

Slowly add the required amount of UniClean 284 while stirring. 

Fill to volume required working volume. 

After warming up to working temperature the bath is ready to use. 
In all work with UniClean 284, make sure that all regulations on 
operations with caustic alkalines are carefully observed! 
5. Working Parameters 
Temperature 
For copper and brass: 
70 °C (60 - 80 °C) 
For steel and iron: 
60 °C (50 - 70 °C) 
Immersion time 
For copper and copper alloys
cathodic: 
1 - 5 minutes 
For zinc die castings
cathodic: 
1 - 3 minutes 
pH 
> 12 
Density 
Cannot be used for monitoring 
Current density 
For copper and copper alloys 
2 - 4 A/dm

For zinc die castings 
1 - 4 A/dm
2


UniClean 284 
Electrolytical cleaner for zinc die castings, brass and copper 
Version: 01 
Doc.-No.: 5200 
Page: 4 / 7 
Released on: 
 
 
Released by: 
10.11.2011 
BTT CSP 
6. Maintenance 
In order to reach a constant cleaner effect, the cleaner solution needs to be added with UniClean 284 in 
regular periods. This occurs according to analytical values or empirical values. 
7. SAP No. for Make - Up and Maintenance Products 
PRODUCT 
SAP No. 
UNICLEAN 284 
1667146 
8. General Safety Precautions 
Avoid direct contact with this material. Do not inhale associated mist or vapors. Wash contaminated clothing 
before reuse. Refer to Material Safety Data Sheet (MSDS) for specific precautions before handling this 
material and for first aid recommendations. As applicable, keep exposure below the limits recommended by 
the appropriate regional regulatory agencies. 
For further information on product safety refer to the corresponding MSDS. The 
MSDS is enclosed at the first delivery of a product. Otherwise a MSDS for a product 
is available on request from the appropriate regional Atotech office. 
 


UniClean 284 
Electrolytical cleaner for zinc die castings, brass and copper 
Version: 01 
Doc.-No.: 5200 
Page: 5 / 7 
Released on: 
 
 
Released by: 
10.11.2011 
BTT CSP 
9. Recommendations for Wastewater Treatment
Rinse water and Concentrates can be treated by a neutralization precipitation. 
Concentrates should be diluted with the rinse water in the ratio of 1:3 and then neutralized 
with caustic soda / calcium hydroxide to pH 9-10 . 
For better flocculation add flocculation agent (recommended is polyacryl amide/anionic with a molecular 
weight of 4-6 million) and stir. Allow the precipitate to settle for better filtration.

tải về 54.76 Kb.

Chia sẻ với bạn bè của bạn:
1   2   3   4   5




Cơ sở dữ liệu được bảo vệ bởi bản quyền ©hocday.com 2024
được sử dụng cho việc quản lý

    Quê hương